Cranium Rubber Craft
Lahore · foam & rubber cutting for auto OEMs
Custom cut · to your drawing · Lahore, Pakistan

Foam and rubber parts, cut to your drawing

Die-cut, CNC-cut, slit, laminated and adhesive-backed foam and rubber components for OEMs and their tier suppliers in Pakistan's automotive industry. Send a drawing or a sample; get a quote, a sample batch, then production on your schedule.

Technical drawing of a die-cut foam gasket, 356 by 176 mm, with four 28 mm holes and a centre cut-out356.0176.0200.0Ø28Ø28PART GASKET-NVH-01MAT EPDM 3.0 mm, PSA one sideSCALE 1:2
All dimensions in mmTolerance quoted per partSheet 1 of 1
01 — MATERIALS

What we cut

Sheet and roll stock cut to shape, with or without an adhesive backing. If your part is drawn in a material not listed here, ask; the cutting is the same.

MaterialTypical use in a vehicleNotes
PU (polyurethane) foamCushioning pads, anti-rattle blocks, trim backing, filler pads behind panelsOpen-cell; range of densities; cut from sheet or block
EVA, PE and XLPE foamClosed-cell gaskets, NVH pads, water-shedding seals, dashboard and console padsClosed-cell, does not take water; easy to adhesive-back
EPDM, neoprene and rubber sheetGaskets, door and lamp seals, grommets, anti-vibration pads, bump stopsSolid or sponge grades; weather and heat resistant
Felt and non-wovenAnti-squeak strips, panel liners, sound-absorbing padsCut flat or with adhesive backing
Foam and rubber tapesSealing strips, glazing tape, anti-vibration stripsSlit to width, kiss-cut on liner, cut to length
Heat-resistant masking stickersMasking nuts, studs and threads through the paint shop so they come out cleanWithstand the paint-oven cycle; peel off after; cut to the nut size you use
02 — PROCESSES

How we cut it

The process is chosen per part: by the material, the shape, the quantity and the tolerance on the drawing.

Die cutting

PRESS · STEEL-RULE DIE · REPEAT RUNS

A steel-rule die made to your drawing, then pressed through the sheet. The right choice for production quantities: fast, repeatable, and the die stays with your part for every repeat order.

Kiss cutting

CUT THROUGH THE PART, NOT THE LINER

Adhesive-backed parts cut on their release liner, supplied on sheets or rolls so the assembly line peels and places. No loose pieces, no lost parts.

CNC knife cutting

NO TOOLING · FROM A DXF OR PDF

A computer-driven knife follows the drawing directly. Best for prototypes, sample batches, short runs and shapes that change between revisions, because there is no die to make or remake.

Slitting and cut-to-length

ROLLS AND STRIPS

Rolls slit to the width you need and strips cut to length, for seals, tapes and liners that run along a panel or a door.

Laminating

FOAM TO FOAM · FOAM TO FABRIC · FOAM TO RUBBER

Two or more layers bonded into one sheet before cutting, so a part that needs a soft face and a firm back, or a foam core under a wear surface, arrives as one piece.

Adhesive backing

PRESSURE-SENSITIVE · ONE OR BOTH SIDES

Pressure-sensitive adhesive applied to one or both faces, with a release liner, matched to the surface the part will stick to: painted steel, plastic trim or glass.

03 — TYPICAL PARTS

Parts we make

Every part is made to the customer's drawing or sample; these are the kinds of part that come through the shop.

NVH pads

Foam and felt pads that stop panels buzzing and rattling: behind door trims, under the dashboard, around the console.

Gaskets and seals

Flat gaskets, lamp seals, flange seals and door seals in EPDM, neoprene, sponge rubber or closed-cell foam.

Anti-vibration pads

Rubber and dense foam pads and bump stops where a part meets the body.

Adhesive strips and tapes

Sealing and anti-squeak strips supplied on liner, cut to length, ready for the line.

Trim and seat foam

Cut and laminated foam for trim backing, armrests, headrests and seat details.

Paint-shop masking

Heat-resistant stickers that cover nuts, studs and threads through painting and baking, then peel off clean.

04 — HOW AN ORDER RUNS

From drawing to delivery

Six steps, in this order, every time. The sample batch is where tolerance, material and adhesive are confirmed before any tooling is cut for production.

  1. STEP 1

    Drawing or sample

    Send a drawing (PDF, DXF or a photo with dimensions), or a physical sample of the part.

  2. STEP 2

    Quote

    Material, process, tooling if any, unit price by quantity, and lead time.

  3. STEP 3

    Sample batch

    A small batch in the final material for your fit check and line trial.

  4. STEP 4

    Approval

    You sign off the sample; that sample becomes the reference for production.

  5. STEP 5

    Production

    Tooling made if the process needs it; batches run to your schedule and quantity.

  6. STEP 6

    Delivery

    Packed by part number, delivered to your plant in Lahore or dispatched by transport anywhere in Pakistan.

Why OEMs send us the drawing

One shop for foam, rubber and adhesive

  • Foam, rubber, felt and tape under one roof, so a part that needs two materials is one order, not two suppliers.
  • Die or CNC, chosen for your quantity: no tooling charge for prototypes, a die for the long run.
  • Adhesive backing matched to the surface, applied before cutting, supplied on liner for the line.
  • Paint-shop masking cut to your nut and stud sizes, made to survive the oven.
  • Made in Lahore, close to the assembly plants and tier suppliers of Punjab, with dispatch across Pakistan.
  • Repeat orders run from the approved sample and the stored tooling, so part number 2 looks like part number 1.
05 — QUESTIONS

Questions buyers ask first

What do you need to quote a part?

A drawing (PDF or DXF) or a sample of the part, the material if you have chosen one, the thickness, and the quantity per order or per month. If the material is undecided, say what the part does and where it sits and we propose one.

Do you make prototypes and small batches?

Yes. CNC knife cutting needs no tooling, so prototypes and sample batches are cut straight from the drawing. A steel-rule die is made only when the part goes into production quantities.

Can parts come with adhesive already applied?

Yes. Pressure-sensitive adhesive on one or both faces, with a release liner, matched to the surface the part sticks to. Adhesive-backed parts are usually kiss-cut on the liner and supplied on sheets or rolls for the assembly line.

Which materials do you cut?

PU (polyurethane) foam, EVA, PE and XLPE closed-cell foams, EPDM, neoprene and other rubber sheet, felt and non-woven, foam and rubber tapes, and heat-resistant masking stickers used on nuts and studs through the paint shop.

Where are you and where do you deliver?

The workshop is in Lahore. Parts are delivered to plants in and around Lahore and dispatched by transport anywhere in Pakistan.

06 — REQUEST A QUOTE

Tell us about the part

Fill in what you know; the message is written for you on the right. Copy it into an email or WhatsApp, and attach the drawing or a photo of the sample.

Your message
Fill in the form and press "Write the message".
Send it to
Cranium Rubber Craft, LahoreWhatsApp: +92 321 4477040Email: incproductsboard@gmail.com